Language
VAT
RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector
This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CPN-1AU:Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-COutput Connector: USB-A 1.1 (Peripheral output - 500mAh)Transfer-Speed: 12MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM60CPN-1AU holder is supplied.
€116.12
Availability:
Out of stock
SKU
RAM-HOL-SAM60CPN-1AU
This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CPN-1AU:Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-COutput Connector: USB-A 1.1 (Peripheral output - 500mAh)Transfer-Speed: 12MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM60CPN-1AU holder is supplied.
| Manufacturer | RAM MOUNT |
|---|
This product also comes in these different configurations:
Zebra Universal Scanner Holder
Universal Scanner Holder, AMPS: 1.181-inch x 1.496-inch, typically mounted on forklifts
SKU
RAP-396U
Warranty
Quantity
0
Price
€55.98
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12U:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCan be used with and without rugged bootCompatible with OEM hand strapAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12U holder is supplied.
SKU
RAM-HOL-HON12U
Warranty
Quantity
0
Price
€89.73
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PU holder is supplied.
SKU
RAM-HOL-HON12PU
Warranty
Quantity
0
Price
€144.97
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2HLU holder is supplied.
SKU
RAM-HOL-ZE25PD2HLU
Warranty
Quantity
0
Price
€341.33
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanAdditional information: This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CPU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62CPU
Warranty
Quantity
0
Price
€151.39
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC8300
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDHLU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDHLU holder is supplied.
SKU
RAM-HOL-ZE26PDHLU
Warranty
Quantity
1
Price
€204.78
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET40/45 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PD2KLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE21PD2U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PD2KLU holder is supplied.
SKU
RAM-HOL-ZE21PD2KLU
Warranty
Quantity
0
Price
€177.74
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET40 & ET45 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCK-ZE21PD2U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PD2U holder is supplied.
SKU
RAM-HOL-ZE21PD2U
Warranty
Quantity
0
Price
€139.40
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PU:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PU holder is supplied.
SKU
RAM-HOL-ZE22PU
Warranty
Quantity
0
Price
€159.76
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22U holder is supplied.
SKU
RAM-HOL-ZE22U
Warranty
Quantity
0
Price
€136.91
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM76CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM76CPU holder is supplied.
SKU
RAM-GDS-DOCK-SAM76CPU
Warranty
Quantity
0
Price
€148.99
Out of stock
RAM Mounts IntellìSkin Next Gen Protective Sleeve for Zebra ET40 & ET45 (8“) - GDS-Technology - External USB-C Connector
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Zebra ET40 & ET45 (8“) and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.An additional USB-C port at the bottom allows the device to be charged even without a dock.Thanks to its thoughtful design, all device functions remain fully accessible the camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs.The IntelliSkin Next Gen protective sleeve for the Zebra ET4x is compatible with a variety of GDS docks and accessories.Product features RAM Mounts RAM-GDS-SKIN-ZE20C-NG:Compatible with standard and extended battery packs and OEM hand strapContinued access to camera and buttonsCharging and data sync functionEasy insertion and removalPorts: External USB-C 2.0Transfer Speed:USB 3.1 @ 5 Gbps (via Pogo-Pins)USB 2.0 @ 480 Mbps (via External USB-C Port)Certifications: RoHS, WEEE, CE & UKCAAdditional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.External USB-C Port on this IntelliSkin is for power only and will not allow data transfer.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE20C-NG is supplied.
SKU
RAM-GDS-SKIN-ZE20C-NG
Warranty
Quantity
0
Price
€100.81
Out of stock
RAM Mounts IntellìSkin for Zebra EM45 & EM45 RFID - GDS-Technology, External USB-C Port, without Belt Clip
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra EM45 / EM45 RFID and offers reliable protection combined with convenient charging functionality. The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use. This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all functions remain fully accessible: the camera and buttons can still be used without restriction. The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE37-C-NC:Compatible with GDS DocksContinued access to camera and buttonsCharging and data sync functionInput Connector: USB-CTransfer Speed: up to USB 3.1 @ 5Gbps (via D-Shape Contacts), up to USB 2.0 @ 480Mbps (via External USB-C Port)Easy insertion and removalAdditional information: Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-ZE37-C-NC is supplied.
SKU
RAM-GDS-SKIN-ZE37-C-NC
Warranty
Quantity
0
Price
€77.01
Out of stock
RAM Mounts IntellìSkin for Zebra EM45 & EM45 RFID - GDS-Technology, without Belt Clip
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra EM45 & EM45 RFID and offers reliable protection combined with convenient charging functionality. The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all functions remain fully accessible: the camera and buttons can still be used without restriction. The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE37-NC:Compatible with GDS DocksContinued access to camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-ZE37-NC is supplied.
SKU
RAM-GDS-SKIN-ZE37-NC
Warranty
Quantity
0
Price
€79.16
Out of stock
RAM Mounts GDS Desktop Dock mit Power Delivery for Smartphones and Tablets - In IntelliSkin Next Gen Protective Sleeve - DeX Support (Next Gen) - USB-C Connector - Gray
This RAM Mounts GDS Desktop Dock with Power Delivery is suitable for smartphones and tablets in IntelliSkin Next Gen, IntelliSkin & IntelliSkin HD protective sleeves.The charging station offers data connectivity via USB-C and the charging function.It is also ideal for permanent use (insertion/removal).Product features RAM Mounts RAM-GDS-DOCK-D2CM-NDU-GRY:Only compatible with IntelliSkin Next Gen protective sleeveEasy insertion and removalPower Delivery & DeX Support (Next Gen)Input Connector: USB-COutput Voltage:5V @ 2A5V @ 3A12V @ 1.5A12V @ 3AOutput Power: 48W TotalProduct dimensions:Height: 5,08 cmWidth: 7,62 cmDepth: 10,41 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-D2CM-NDU-GRY Dock is supplied.
SKU
RAM-GDS-DOCK-D2CM-NDU-GRY
Warranty
Quantity
0
Price
€136.15
Out of stock
RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connector
This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKF-SAM62CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmIncludes built-in 12-VDC Axial cooling fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKF-SAM62CPU holder is supplied.
SKU
RAM-GDS-DOCKF-SAM62CPU
Warranty
Quantity
0
Price
€205.91
Out of stock
RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Power Supply
This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 & Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKF-SAM62CU:Compatible with GDS hand-stand & moreEasy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3ATransfer Speed: 5GbpsInput Cable Length: ca. 21 cmIncludes built-in 12-VDC Axial cooling fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKF-SAM62CU holder is supplied.
SKU
RAM-GDS-DOCKF-SAM62CU
Warranty
Quantity
0
Price
€231.78
Out of stock
RAM Mounts GDS Cool-Dock Holder (Latch) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Cool-Dock (Latch) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKF-SAM78CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmIncludes built-in 12-VDC Axial cooling fanAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKF-SAM78CPU holder is supplied.
SKU
RAM-GDS-DOCKF-SAM78CPU
Warranty
Quantity
0
Price
€204.99
Out of stock
RAM Mounts GDS Cool-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - With Fan - USB-C Connector
This RAM Mounts GDS Cool-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKLF-SAM62CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmIncludes built-in 12-VDC Axial cooling fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLF-SAM62CPU holder is supplied.
SKU
RAM-GDS-DOCKLF-SAM62CPU
Warranty
Quantity
0
Price
€226.40
Out of stock
RAM Mounts GDS Cool-Dock Holder (Key-Locking) for Samsung Tab S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Cool-Dock (Key-Locking) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock including a built-in 12-VDC Axial cooling fan with a 2.2 meter long hardwire power cord.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKLF-SAM78CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmIncludes built-in 12-VDC Axial cooling fanAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLF-SAM78CPU holder is supplied.
SKU
RAM-GDS-DOCKLF-SAM78CPU
Warranty
Quantity
0
Price
€205.13
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C & Dual USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the dual USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLL-U1CD2U:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per port)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 362 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLL-U1CD2U holder is supplied.
SKU
RAM-GDS-DOCKLL-U1CD2U
Warranty
Quantity
0
Price
€172.24
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLL-U1CDU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 322 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLL-U1CDU holder is supplied.
SKU
RAM-GDS-DOCKLL-U1CDU
Warranty
Quantity
0
Price
€154.60
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-C port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLL-U1CP-CU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5 - 12V @ 3AOutput Connector: USB-C (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 317 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLL-U1CP-CU holder is supplied.
SKU
RAM-GDS-DOCKLL-U1CP-CU
Warranty
Quantity
0
Price
€150.45
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Left) - 2-Hole AMPS Pattern - USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Left) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLL-U1CPU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AInput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 322 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLL-U1CPU holder is supplied.
SKU
RAM-GDS-DOCKLL-U1CPU
Warranty
Quantity
0
Price
€121.35
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Right) - 2-Hole AMPS Pattern - USB-C & Dual USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Right) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the dual USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLR-U1CD2U:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per port)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 362 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLR-U1CD2U holder is supplied.
SKU
RAM-GDS-DOCKLR-U1CD2U
Warranty
Quantity
0
Price
€172.24
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - Key-Locking (Rechts) - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Rechts) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLR-U1CDU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 322 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLR-U1CDU holder is supplied.
SKU
RAM-GDS-DOCKLR-U1CDU
Warranty
Quantity
0
Price
€154.60
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Right) - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Right) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-C port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLR-U1CP-CU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5 - 12V @ 3AOutput Connector: USB-C (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 317 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLR-U1CP-CU holder is supplied.
SKU
RAM-GDS-DOCKLR-U1CP-CU
Warranty
Quantity
0
Price
€150.45
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM62CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM62CDU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM62CDU
Warranty
Quantity
0
Price
€249.99
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM80CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM80CPU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM80CPU
Warranty
Quantity
0
Price
€176.31
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5-inch (SM-X200) in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM83CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM83CDU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM83CDU
Warranty
Quantity
0
Price
€196.94
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A8 10.5-inch (SM-X200) in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM83CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM83CPU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM83CPU
Warranty
Quantity
0
Price
€142.90
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Protective Sleeve - USB-C & Dual USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM88CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cm· Prepared for GDS 12-VDC Axial cooling fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM88CD2U holder is supplied.
SKU
RAM-GDS-DOCKL-SAM88CD2U
Warranty
Quantity
0
Price
€285.88
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM88CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM88CDU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM88CDU
Warranty
Quantity
0
Price
€272.86
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU:Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanIncluding RAM NFC-ExtenderAdditional information: This product is not compatible with the GDS Hand-Stand.This holder will not support any NFC functionality of the Tab Active2Potential interference of NFC functionality may occur when positioned close to strong magnets.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM62CP-NFCU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM62CP-NFCU
Warranty
Quantity
0
Price
€285.24
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab Active2, Active3 & Active5 - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM62CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationLockable with keyInput Connector: USB-C 3.1Power Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM62CU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM62CU
Warranty
Quantity
0
Price
€217.54
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM76CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM76CPU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM76CPU
Warranty
Quantity
0
Price
€164.84
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM76CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationLockable with keyInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM76CU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM76CU
Warranty
Quantity
0
Price
€192.33
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Case - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM78CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM78CPU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM78CPU
Warranty
Quantity
0
Price
€168.93
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab S7, Tab S9 & Tab S9 FE in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM78CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationLockable with keyInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 35 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM78CU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM78CU
Warranty
Quantity
0
Price
€199.89
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A9 & A7 Lite 8.7-inch - in IntelliSkin Protective Sleeve - USB-C & Dual USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9 & A7 Lite 8.7-inch in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM80CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cm· Prepared for GDS 12-VDC Axial cooling fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM80CD2U holder is supplied.
SKU
RAM-GDS-DOCKL-SAM80CD2U
Warranty
Quantity
0
Price
€245.75
Out of stock
RAM Mounts GDS Tough-Dock Holder (Key-Locking) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM80CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-SAM80CDU holder is supplied.
SKU
RAM-GDS-DOCKL-SAM80CDU
Warranty
Quantity
0
Price
€234.40
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock With Key-Locking - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder with key-locking is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-C port allows you to integrate a peripheral device into your setup.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCKL-V12-U1CP-CU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalKey lockingCharging functionInput Connector: USB-C & USB-C (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-U1CP-CU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-U1CP-CU
Warranty
Quantity
0
Price
€196.80
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock With Key-Locking - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Heated Pogo-Pins - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder with key-locking is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-A port allows you to integrate a peripheral device into your setup.The heated pogo pins ensure a reliable connection and effectively prevent the contacts from freezing or becoming blocked by ice.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCKL-V12-U1CPDHU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalHeated Pogo-PinsKey lockingCharging functionInput Connector: USB-C & USB-A (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-U1CPDHU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-U1CPDHU
Warranty
Quantity
0
Price
€219.76
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock With Key-Locking - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder with key-locking is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-A port allows you to integrate a peripheral device into your setup.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCKL-V12-U1CPDU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalKey lockingCharging functionInput Connector: USB-C & USB-A (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-U1CPDU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-U1CPDU
Warranty
Quantity
0
Price
€193.74
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock mit Schlüsselverriegelung - 2-Hole AMPS Pattern - USB-C Connector - Heated Pogo-Pins - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder with key-locking is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.The heated pogo pins ensure a reliable connection and effectively prevent the contacts from freezing or becoming blocked by ice.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCKL-V12-U1CPHU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalHeated Pogo-PinsKey lockingCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-U1CPHU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-U1CPHU
Warranty
Quantity
0
Price
€178.43
Out of stock
RAM Mounts GDS Holder (Key-Locking) for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - Heated Pogo-Pins - USB-C & USB-A Connector
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDHU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionHeated Pogo-PinsLockable with keyInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE2434CPDHU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE2434CPDHU
Warranty
Quantity
0
Price
€185.16
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - Dual USB-C Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-C cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62C-CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-C (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62C-CU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62C-CU
Warranty
Quantity
0
Price
€217.01
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM80CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM80CPU holder is supplied.
SKU
RAM-GDS-DOCK-SAM80CPU
Warranty
Quantity
0
Price
€145.50
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9 & A7 Lite (8.7-inch) - in IntelliSkin Next Gen Protective Sleeve - Multi-Mode - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder with Multi-Mode is suitable for the Samsung Tab A9 & A7 Lite 8.7-inch in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.Mutli-mode is integrated into the dock allowing centralized AI systems to perform as the host instead of the tablet, turning your IntelliSkin-wrapped tablet into a peripheral. There is no button or switch that turns this function on and off—Multi-Mode is automatically activated when the device is docked.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM80-MMU:Compatible with GDS hand-stand Easy insertion and removalCharging functionMulti-modeWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3A max (Peripheral: 5V - 900mA max)Output Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM80-MMU holder is supplied.
SKU
RAM-GDS-DOCK-SAM80-MMU
Warranty
Quantity
0
Price
€190.95
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A8 10.5-inch (SM-X200) in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM83CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM83CDU holder is supplied.
SKU
RAM-GDS-DOCK-SAM83CDU
Warranty
Quantity
0
Price
€175.03
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A8 (10.5“) - in IntelliSkin Next Gen Protective Sleeve - USB-C Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A8 10.5-inch (SM-X200) in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM83CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM83CPU holder is supplied.
SKU
RAM-GDS-DOCK-SAM83CPU
Warranty
Quantity
0
Price
€139.59
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3A maxOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CD2U holder is supplied.
SKU
RAM-GDS-DOCK-SAM88CD2U
Warranty
Quantity
0
Price
€252.35
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+ - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.
SKU
RAM-GDS-DOCK-SAM88CDU
Warranty
Quantity
0
Price
€240.63
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CDU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62CDU
Warranty
Quantity
0
Price
€243.44
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 in IntelliSkin Protective Sleeve - NFC-Extender - USB-C Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU:Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanIncluding RAM NFC-ExtenderAdditional information: This product is not compatible with the GDS Hand-Stand.This holder will not support any NFC functionality of the Tab Active2Potential interference of NFC functionality may occur when positioned close to strong magnets.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CP-NFCU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62CP-NFCU
Warranty
Quantity
0
Price
€258.88
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationWith LatchInput Connector: USB-C 3.1Power Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function. Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62CU
Warranty
Quantity
0
Price
€181.76
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - Multi-Mode - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder with Multi-Mode is suitable for the Samsung Tab Active2, Active3 & Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.Mutli-mode is integrated into the dock allowing centralized AI systems to perform as the host instead of the tablet, turning your IntelliSkin-wrapped tablet into a peripheral. There is no button or switch that turns this function on and off—Multi-Mode is automatically activated when the device is docked.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62-MMU:Compatible with GDS hand-stand Easy insertion and removalCharging functionMulti-modeWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3A max (Peripheral: 5V - 900mA max)Output Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62-MMU holder is supplied.
SKU
RAM-GDS-DOCK-SAM62-MMU
Warranty
Quantity
0
Price
€187.41
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7, S9 & S9 FE - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7, S9 & S9 FE in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM76CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationWith LatchInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM76CU holder is supplied.
SKU
RAM-GDS-DOCK-SAM76CU
Warranty
Quantity
0
Price
€176.96
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ 12.4-inch (SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.Data synchronization via the connection is also supported.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM78CU:Compatible with GDS hand-stand Easy insertion and removalCharging functionData synchronizationWith LatchInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM78CU holder is supplied.
SKU
RAM-GDS-DOCK-SAM78CU
Warranty
Quantity
0
Price
€185.19
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM80CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3A maxOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM80CD2U holder is supplied.
SKU
RAM-GDS-DOCK-SAM80CD2U
Warranty
Quantity
0
Price
€248.35
Out of stock
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A7 Lite (8.7“) & A9 - in IntelliSkin Next Gen Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A7 Lite (8.7“) & A9 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM80CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM80CDU holder is supplied.
SKU
RAM-GDS-DOCK-SAM80CDU
Warranty
Quantity
0
Price
€235.58
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - 2-Hole AMPS Pattern - USB-C & Dual USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the dual USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCK-U1CD2U:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 8,02 cmOverall Height: 21,44 cmOverall Depth: 7,70 cmWeight: ca. 223 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-U1CD2U holder is supplied.
SKU
RAM-GDS-DOCK-U1CD2U
Warranty
Quantity
0
Price
€149.71
Out of stock
RAM Mounts GDS Uni-Conn Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-C port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCK-U1CP-CU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5 - 12V @ 3AOutput Connector: USB-C (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 8,02 cmOverall Height: 21,44 cmOverall Depth: 7,70 cmWeight: ca. 223 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-U1CP-CU holder is supplied.
SKU
RAM-GDS-DOCK-U1CP-CU
Warranty
Quantity
0
Price
€134.90
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-C Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-C port allows you to integrate a peripheral device into your setup.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCK-V12-U1CP-CU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalCharging functionInput Connector: USB-C & USB-C (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V-12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-U1CP-CU holder is supplied.
SKU
RAM-GDS-DOCK-V12-U1CP-CU
Warranty
Quantity
0
Price
€164.84
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Heated Pogo-Pins - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-A port allows you to integrate a peripheral device into your setup.The heated pogo pins ensure a reliable connection and effectively prevent the contacts from freezing or becoming blocked by ice.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCK-V12-U1CPDHU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalHeated Pogo-PinsCharging functionInput Connector: USB-C & USB-A (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-U1CPDHU holder is supplied.
SKU
RAM-GDS-DOCK-V12-U1CPDHU
Warranty
Quantity
0
Price
€187.83
Out of stock
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C Connector - Heated Pogo-Pins - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.The heated pogo pins ensure a reliable connection and effectively prevent the contacts from freezing or becoming blocked by ice.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCK-V12-U1CPHU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalHeated Pogo-PinsCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-U1CPHU holder is supplied.
SKU
RAM-GDS-DOCK-V12-U1CPHU
Warranty
Quantity
0
Price
€138.36
Out of stock
RAM Mounts GDS Holder for Zebra EC50 & EC55 in IntelliSkin Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE16CPDU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE16CPDU
Warranty
Quantity
0
Price
€161.58
Out of stock
RAM Mounts GDS Holder for Zebra TC2x & TC5x Series in IntelliSkin Protective Sleeve - USB-C & USB-A Connector
This RAM Mounts GDS holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE2434CPDU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE2434CPDU
Warranty
Quantity
0
Price
€132.21
Out of stock
RAM Mounts GDS Holder (Key-Locking) for Zebra EC50/55
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE16CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with KeysInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE16CPDU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE16CPDU
Warranty
Quantity
2
Price
€162.06
RAM Mounts GDS Holder for Zebra EC50/55
This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE16CPU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE16CPU
Warranty
Quantity
2
Price
€132.31
RAM Mounts GDS Holder (Key-Locking) for Zebra TC22/27 & TC53/58
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with keyInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE2434CPDU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE2434CPDU
Warranty
Quantity
1
Price
€161.54
RAM Mounts GDS Holder (Key-Locking) for Zebra TC22/27 & TC53/58
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with keyInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE2434CPU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE2434CPU
Warranty
Quantity
2
Price
€131.78
RAM Mounts GDS Holder (Key-Locking) for Zebra TC73/78
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC73 & TC78 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra TC7x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE35CPDHU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionHeated Pogo-PinsLockable with keyInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE35-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE35CPDHU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE35CPDHU
Warranty
Quantity
2
Price
€185.63
RAM Mounts GDS Holder (Key-Locking) for Zebra TC73/78
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC73 & TC78 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra TC7x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE35CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with KeysInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE35-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE35CPDU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE35CPDU
Warranty
Quantity
2
Price
€162.04
RAM Mounts GDS Holder (Key-Locking) for Zebra TC73/78
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC73 & TC78 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra TC7x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE35CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with KeysInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE35-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE35CPU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE35CPU
Warranty
Quantity
2
Price
€132.27
RAM Mounts GDS Form-Fit Holder (Latch) for Zebra ET40/45 (8-inch)
This RAM Mounts GDS Form-Fit (Latch) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKNLL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveWith LatchInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKNLL-ZE20PU holder is supplied.
SKU
RAM-GDS-DOCKNLL-ZE20PU
Warranty
Quantity
0
Price
€128.18
Out of stock
RAM Mounts GDS Form-Fit Holder (Latch) for Zebra ET40/45 (10-inch)
This RAM Mounts GDS Form-Fit (Latch) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKNLL-ZE21PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveWith LatchInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKNLL-ZE21PU holder is supplied.
SKU
RAM-GDS-DOCKNLL-ZE21PU
Warranty
Quantity
0
Price
€133.66
Out of stock
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PD2U holder is supplied.
SKU
RAM-GDS-DOCK-ZE20PD2U
Warranty
Quantity
3
Price
€156.54
RAM Mounts GDS Holder for Zebra EC50/55
This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE16CPU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE16CPU
Warranty
Quantity
2
Price
€98.88
RAM Mounts GDS Holder for Zebra TC22/27 & TC53/58
This RAM Mounts GDS holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the IntelliSkin protective sleeve for the Zebra handheld.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE2434CPU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE2434CPU
Warranty
Quantity
0
Price
€97.70
Out of stock
RAM Mounts GDS Holder for Zebra TC73/78
This RAM Mounts GDS holder is suitable for Zebra TC73 & TC78 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra TC7x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE35CPDU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE35-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE35CPDU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE35CPDU
Warranty
Quantity
2
Price
€132.68
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PU holder is supplied.
SKU
RAM-GDS-DOCKL-ZE20PU
Warranty
Quantity
0
Price
€174.76
Out of stock
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PU holder is supplied.
SKU
RAM-GDS-DOCK-ZE20PU
Warranty
Quantity
1
Price
€113.11
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab Active3 & Active5 - in IntelliSkin Next Gen Protective Sleeve - USB-C & Dual USB-A Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CD2U:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM62CD2U holder is supplied.
SKU
RAM-GDS-DOCK-SAM62CD2U
Warranty
Quantity
0
Price
€254.43
Out of stock
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE20PDU holder is supplied.
SKU
RAM-GDS-DOCK-ZE20PDU
Warranty
Quantity
3
Price
€146.84
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE21PD2U holder is supplied.
SKU
RAM-GDS-DOCK-ZE21PD2U
Warranty
Quantity
0
Price
€158.53
Out of stock
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE21PU holder is supplied.
SKU
RAM-GDS-DOCK-ZE21PU
Warranty
Quantity
0
Price
€115.43
Out of stock
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE21PD2U holder is supplied.
SKU
RAM-GDS-DOCKL-ZE21PD2U
Warranty
Quantity
0
Price
€255.03
Out of stock
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE21PU holder is supplied.
SKU
RAM-GDS-DOCKL-ZE21PU
Warranty
Quantity
0
Price
€181.71
Out of stock
RAM Mounts GDS Holder for Zebra TC73/78
This RAM Mounts GDS holder is suitable for Zebra TC73 & TC78 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra TC7x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE35CPU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-CInput Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE35-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-ZE35CPU holder is supplied.
SKU
RAM-GDS-DOCK-V12-ZE35CPU
Warranty
Quantity
3
Price
€98.27
RAM Mounts GDS Holder (Key-Locking) for Zebra EC50/55
This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device’s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE16CPDHU:Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionHeated Pogo-PinsLockable with KeysInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 100 cmAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE16-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-ZE16CPDHU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-ZE16CPDHU
Warranty
Quantity
2
Price
€222.60
RAM Mounts GDS Uni-Conn Charging Dock with Key-Locking (Rechts) - 2-Hole AMPS Pattern - USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder with Key-Locking (Rechts) is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCKLR-U1CPU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionKey-LockingEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AInput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 10.85 cmOverall Height: 21.44 cmOverall Depth: 7.70 cmWeight: ca. 322 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKLR-U1CPU holder is supplied.
SKU
RAM-GDS-DOCKLR-U1CPU
Warranty
Quantity
1
Price
€121.35
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock With Key-Locking - 2-Hole AMPS Pattern - USB-C Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder with key-locking is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCKL-V12-U1CPU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalKey lockingCharging functionInput Connector: USB-CAusgangsleistung: 15WAusgangsspannung: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-V12-U1CPU holder is supplied.
SKU
RAM-GDS-DOCKL-V12-U1CPU
Warranty
Quantity
1
Price
€145.55
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab S7 FE, S7+, S8+, S9 FE+, S9+ & S10+ - in IntelliSkin Next Gen Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab S7 FE (SM-T736B), S7+ (12.4“ SM-T970), S8+, S9 FE+, S9+ & S10+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM78CPU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM78CPU holder is supplied.
SKU
RAM-GDS-DOCK-SAM78CPU
Warranty
Quantity
3
Price
€163.08
RAM Mounts GDS Tough-Dock Holder (Latch) for Samsung Tab A9+- in IntelliSkin Next Gen Protective Sleeve - USB-C Connector
This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU:Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.
SKU
RAM-GDS-DOCK-SAM88CPU
Warranty
Quantity
2
Price
€172.15
RAM Mounts GDS Uni-Conn Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.With the USB-A port, you can integrate a peripheral device into your setup.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCK-U1CDU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionEasy insertion and removalCharging function & data transferInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 215 mmOutput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 8,02 cmOverall Height: 21,44 cmOverall Depth: 7,70 cmWeight: ca. 223 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-U1CDU holder is supplied.
SKU
RAM-GDS-DOCK-U1CDU
Warranty
Quantity
1
Price
€132.03
RAM Mounts GDS Uni-Conn Charging Dock - 2-Hole AMPS Pattern - USB-C Connector - Screw Set
The RAM Mounts GDS Uni-Conn Holder is a universal docking station specifically designed for devices in an IntelliSkin protective sleeve with a Uni-Conn adapter.This Snap-In holder securely holds your device while enabling fast charging via integrated Pogo-Pins, with power supplied through a USB-C connection.The docking and undocking process is simple:Insert the tablet with the IntelliSkin protective sleeve and mounted GDS Uni-Conn adapter into the base of the dock and push it back until it snaps into place.To remove it, simply press the lever to release the tablet.For the docking station to function, the GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted on the designated IntelliSkin protective case.Currently, the following devices are compatible with this fixed docking height:Samsung Tab A7 Lite, Tab A 8.4, Tab S9 FE, Tab S9 FE+, Tab Active5, Tab Active3, and Tab A9+.This holder provides a reliable solution for charging and data transfer across various applications.Product features RAM Mounts RAM-GDS-DOCK-U1CPU:Only compatible with IntelliSkin & Uni-Conn adapterSnap-In functionEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput voltage: 5 - 12V @ 3AInput Cable Length: ca. 215 mmProduct dimensions:Overall Width: 8,02 cmOverall Height: 21,44 cmOverall Depth: 7,70 cmWeight: ca. 223 gAdditional information: The Lever Stop included with this dock is required in order to function properly.Warranty on dock is void if dock is used without Lever Stop. GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-U1CPU holder is supplied.
SKU
RAM-GDS-DOCK-U1CPU
Warranty
Quantity
5
Price
€95.99
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C & USB-A Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.An additional USB-A port allows you to integrate a peripheral device into your setup.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCK-V12-U1CPDU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalCharging functionInput Connector: USB-C & USB-A (Peripheral output - 500mAh)Power Output: 15WOutput Voltage: 5V - 12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-U1CPDU holder is supplied.
SKU
RAM-GDS-DOCK-V12-U1CPDU
Warranty
Quantity
1
Price
€161.78
RAM Mounts GDS Uni-Conn Spring Loaded Charging Dock - 2-Hole AMPS Pattern - USB-C Connector - Screw-Set
The RAM Mounts GDS Uni-Conn spring-loaded holder is a universal docking station specifically designed for devices enclosed in an IntelliSkin case with a Uni-Conn adapter.The spring-loaded quick-release mechanism securely holds your device in place while enabling fast charging via the integrated pogo pins, with power supplied through a USB-C connection.The GDS Uni-Conn adapter (RAM-GDS-U1U) must be mounted onto the designated IntelliSkin case for use with this docking station.To place the device with the IntelliSkin case into the dock, the GDS Uni-Conn adapter must be inserted into the octagon connector and pushed upward until the bottom can be seated into the dock.Product features RAM Mounts RAM-GDS-DOCK-V12-U1CPU:Only compatible with IntelliSkin & Uni-Conn adapterEasy insertion and removalCharging functionInput Connector: USB-CPower Output: 15WOutput Voltage: 5V-12V @ 3AInput Cable Length: ca. 100 mmAdditional information: GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts. Consider the GDS Tough-Dock for extreme applications.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V12-U1CPU holder is supplied.
SKU
RAM-GDS-DOCK-V12-U1CPU
Warranty
Quantity
5
Price
€122.45
RAM Mounts GDS Holder for Samsung XCover 6 Pro, XCover 7 Pro & Zebra EM45 - in IntelliSkin Protective Sleeve - USB-C Power Supply
This RAM Mounts GDS holder is suitable for the Samsung XCover 6 Pro or XCover 7 Pro in IntelliSkin protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V3CPAU:Not compatible with hand-strap Spring-loaded design for easy insertion and removalCharging functionInput Connector: USB-COutput Voltage: 20V @ 3AInput Cable Length: ca. 21 cmAdditional information: This dock will not support the XCover6 Pro or XCover 7 Pro when using a Hand Strap accessory.For an alternate dock that supports that hand strap, see RAM-GDS-DOCK-V11CU.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-V3CPAU holder is supplied.
SKU
RAM-GDS-DOCK-V3CPAU
Warranty
Quantity
3
Price
€95.34
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab S10+, S9+ & S9 FE+ - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab S10+, S9+ & S9 FE+ and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM87-NG:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM87-NG is supplied.
SKU
RAM-GDS-SKIN-SAM87-NG
Warranty
Quantity
3
Price
€95.51
RAM Mounts IntellìSkin Next Gen Protective Sleeve for Zebra EC50 & EC55 - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Zebra EC50 & EC55 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin Next Gen protective sleeve for the Zebra EC5x is compatible with a variety of USB 3.1 supported GDS docks and accessories.Product features RAM Mounts RAM-GDS-SKIN-ZE16-NG:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalTransfer Speed: Up to USB 3.1 @ 5 Gbps (via D-Shape Contacts)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE16-NG is supplied.
SKU
RAM-GDS-SKIN-ZE16-NG
Warranty
Quantity
2
Price
€75.94
RAM Mounts IntellìSkin Next Gen Protective Sleeve for Zebra ET40 & ET45 (10“) - GDS-Technology - External USB-C Connector
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Zebra ET40 & ET45 (10“) and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.An additional USB-C port at the bottom allows the device to be charged even without a dock.Thanks to its thoughtful design, all device functions remain fully accessible the camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs.The IntelliSkin Next Gen protective sleeve for the Zebra ET4x is compatible with a variety of GDS docks and accessories.Product features RAM Mounts RAM-GDS-SKIN-ZE21C-NG:Compatible with standard and extended battery packs and OEM hand strapContinued access to camera and buttonsCharging and data sync functionEasy insertion and removalPorts: External USB-C 2.0Transfer Speed:USB 3.1 @ 5 Gbps (via Pogo-Pins)USB 2.0 @ 480 Mbps (via External USB-C Port)Certifications: RoHS, WEEE, CE & UKCAAdditional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.External USB-C Port on this IntelliSkin is for power only and will not allow data transfer.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE21C-NG is supplied.
SKU
RAM-GDS-SKIN-ZE21C-NG
Warranty
Quantity
1
Price
€92.07
RAM Mounts IntellìSkin Protective Sleeve for Zebra TC22 & TC27 - GDS-Technology
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC22 & TC27 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE24:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE24 is supplied.
SKU
RAM-GDS-SKIN-ZE24
Warranty
Quantity
2
Price
€69.24
RAM Mounts IntellìSkin Protective Sleeve for Zebra TC53 & TC58 - GDS-Technology
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC53 & TC58 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE34:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE34 is supplied.
SKU
RAM-GDS-SKIN-ZE34
Warranty
Quantity
3
Price
€67.60
RAM Mounts IntellìSkin Next Gen Protective Sleeve for Zebra TC73 & TC78 - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Zebra TC73 & TC78 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin Next Gen protective sleeve for the Zebra EC5x is compatible with a variety of USB 3.1 supported GDS docks and accessories.Product features RAM Mounts RAM-GDS-SKIN-ZE35-NG:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalTransfer Speed: Up to USB 3.1 @ 5 Gbps (via D-Shape Contacts)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE35-NG is supplied.
SKU
RAM-GDS-SKIN-ZE35-NG
Warranty
Quantity
2
Price
€79.37
RAM Mounts IntellìSkin for Samsung Galaxy XCover7 Pro & XCover6 Pro - GDS-Technology - Gray
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Samsung Galaxy XCover7 Pro & XCover6 Pro and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM84-GRY:Compatible with GDS DocksInlcuded Belt ClipContinued access to camera and buttonsCharging functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM84-GRY is supplied.
SKU
RAM-GDS-SKIN-SAM84-GRY
Warranty
Quantity
0
Price
€74.97
Out of stock
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab A9+ - GDS-Technology - Gray
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab A9+ and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM88-NG-GRY:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM88-NG-GRY is supplied.
SKU
RAM-GDS-SKIN-SAM88-NG-GRY
Warranty
Quantity
0
Price
€118.87
Out of stock
RAM Mounts IntellìSkin Protective Sleeve for Zebra TC53 & TC58 - GDS-Technology - Gray
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC53 & TC58 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE34-GRY:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE34-GRY is supplied.
SKU
RAM-GDS-SKIN-ZE34-GRY
Warranty
Quantity
0
Price
€67.12
Out of stock
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab Active4 Pro & Active5 Pro - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab Active Pro, Active4 Pro & Active5 Pro and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM54-NG-1:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.For connecting GDS Uni-Conn, Adjustable Adapter is required: RAM-GDS-U1AU.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM54-NG-1 is supplied.
SKU
RAM-GDS-SKIN-SAM54-NG-1
Warranty
Quantity
1
Price
€97.89
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab Active3 - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab Active3 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM74-NG:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.This product will not support the -inchNo Battery Mode-inch function of the Tab Active3. To support -inchNo Battery Mode-inch, see RAM Tough-Case.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM74-NG is supplied.
SKU
RAM-GDS-SKIN-SAM74-NG
Warranty
Quantity
3
Price
€92.74
RAM Mounts IntellìSkin for Samsung Galaxy XCover7 Pro & XCover6 Pro - GDS-Technology
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Samsung Galaxy XCover7 Pro & XCover6 Pro and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM84:Compatible with GDS DocksInlcuded Belt ClipContinued access to camera and buttonsCharging functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM84 is supplied.
SKU
RAM-GDS-SKIN-SAM84
Warranty
Quantity
0
Price
€76.43
Out of stock
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab A9+ - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab A9+ and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM88-NG:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM88-NG is supplied.
SKU
RAM-GDS-SKIN-SAM88-NG
Warranty
Quantity
0
Price
€109.33
Out of stock
RAM Mounts IntellìSkin Hard Case for Samsung Galaxy Tab Active3 & Active5 - External USB-C Port - GDS-Technology
This RAM Mounts GDS IntelliSkin Hard Case protective sleeve is designed for the Samsung Galaxy Tab Active3 & Active5 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM89-HC:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations. Samsung Tab Active5 allows a maximum transfer speed of USB 2.0.This product will not support the -inchNo Battery Mode-inch.To support -inchNo Battery Mode-inch, see RAM Tough-Case.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM89-HC is supplied.
SKU
RAM-GDS-SKIN-SAM89-HC
Warranty
Quantity
1
Price
€96.97
RAM Mounts IntellìSkin Next Gen for Samsung Galaxy Tab Active5 - GDS-Technology
This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab Active5 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM90-NG:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer Speed:Up to USB 3.1 @ 5Gbps (via D-Shape Contacts*)Up to USB 2.0 @ 480Mbps (via External USB-C Port)Additional information: *USB 3.1 is the maximum transfer speed that the IntelliSkin can support, but actual transfer speeds will vary based on selected docks, chargers, and device limitations.This product will not support the -inchNo Battery Mode-inch.To support -inchNo Battery Mode-inch, see RAM Tough-Case.Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM90-NG is supplied.
SKU
RAM-GDS-SKIN-SAM90-NG
Warranty
Quantity
0
Price
€94.00
Out of stock
RAM Mounts IntellìSkin for Samsung Galaxy XCover7 - GDS-Technology
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Samsung Galaxy XCover7 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all functions remain fully accessible: the camera, buttons, and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations, making it ideal for professional use – whether in vehicles, at the workplace, or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM94:Compatible with GDS DocksInlcuded Belt ClipContinued access to camera and buttonsCharging functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM94 is supplied.
SKU
RAM-GDS-SKIN-SAM94
Warranty
Quantity
10
Price
€75.57
RAM Mounts IntellìSkin Protective Sleeve for Zebra TC22 & TC27 - GDS-Technology - Gray
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC22 & TC27 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE24-GRY:Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner, camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE24-GRY is supplied.
SKU
RAM-GDS-SKIN-ZE24-GRY
Warranty
Quantity
1
Price
€68.90
RAM Mounts IntellìSkin for Zebra EM45 & EM45 RFID - GDS-Technology
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra EM45 & EM45 RFID and offers reliable protection combined with convenient charging functionality. The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all iPhone functions remain fully accessible: the camera and buttons can still be used without restriction. The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE37:Compatible with GDS DocksContinued access to camera and buttonsCharging and data sync functionEasy insertion and removalIncludes Belt-ClipAdditional information: The metal belt clip may interfere with RFID and NFC functionality in certain applications. To avoid this, you may either remove the clip or see the non-clip version, RAM-GDS-SKIN-ZE37-NC. Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-ZE37 is supplied.
SKU
RAM-GDS-SKIN-ZE37
Warranty
Quantity
0
Price
€69.31
Out of stock
RAM Mounts IntellìSkin for Zebra EM45 - GDS-Technology, External USB-C Port
This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra EM45 and offers reliable protection combined with convenient charging functionality. The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use. This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all functions remain fully accessible: the camera and buttons can still be used without restriction. The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE37-C:Compatible with GDS DocksContinued access to camera and buttonsCharging and data sync functionInput Connector: USB-CTransfer Speed: up to USB 3.1 @ 5Gbps (via D-Shape Contacts), up to USB 2.0 @ 480Mbps (via External USB-C Port)Easy insertion and removalIncludes Belt-ClipAdditional information: The metal belt clip may interfere with RFID and NFC functionality in certain applications. To avoid this, you may either remove the clip or see the non-clip version, RAM-GDS-SKIN-ZE37-C-NC. Devices shown are not included in the delivery. Only the RAM-GDS-SKIN-ZE37-C is supplied.
SKU
RAM-GDS-SKIN-ZE37-C
Warranty
Quantity
0
Price
€79.05
Out of stock
RAM Mounts GDS Uni-Conn Adapter for IntelliSkin Protective Sleeves - Screw Set - Grey
This GDS Uni-Conn adapter is designed for selected IntelliSkin protective sleeves to make them compatible with the Uni-Conn system.The octagon-shaped adapter is easy to install before inserting the device into the protective sleeve.When it's time to upgrade your device fleet, simply replacing the IntelliSkin protective sleeve is all that’s needed.With its high compatibility, this adapter provides a reliable solution for seamless device integration into the Uni-Conn system.Product features RAM Mounts RAM-GDS-U1U-GRY:Compatible with IntelliSkin Next Gen, Hard Case, and Thin-Case seriesEasy insertion and removalScrew Set includedAdditional information: Please note that this adapter is not compatible with certain devices in IntelliSkin, such as:Apple iPad Pro 11-inch (1st - 4th Gen.), iPad Air 4, Air 5, Air 11 (M2), iPad 10th Gen., iPad Pro 12.9 (3rd - 6th Gen.),iPad mini 6 & A17 Pro, Samsung Tab A 10.1, Tab A 10.5, Tab A 8.0 (2018), Tab A7 10.4, Tab Active Pro, Tab Active4 Pro, Tab S7, Tab S7+, Tab S7 FE, Tab S8+.For these device models, the adjustable adapter RAM-GDS-U1AU is recommended.Devices shown are not included in the delivery.Only the RAM-GDS-U1U-GRY adapter is supplied.
SKU
RAM-GDS-U1U-GRY
Warranty
Quantity
0
Price
€31.48
Out of stock
RAM Mounts X-Grip Clamp for Tablets (7–8 inches)
Sometimes, its all about the design. If you are looking for a compact mount for your tablet without that cookie cutter shape, you've found it. The RAM X-Grip II has a clean and clever four leg design that sports great holding power without hiding your tablet behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the RAM X-Grip II is the tablet holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your tablet and become the most useful accessory in your vehicle.The RAM X-Grip II consists of a spring loaded holder and 1-inch rubber ball connected to the back of the base. Included are extra easy access grip knobs, located on the back of the holder for quick release of your tablet. The holder expands and contracts for perfect fit of most 7-inches tablets.Compatible Devices:• Amazon Kindle• Amazon Kindle Fire• Apple iPad mini• Archos 7• Asus EEE Pad Memo• Barnes & Noble NOOKcolor• BlackBerry PlayBook• Dell Streak 7• HTC Flyer• Panasonic Toughpad JT-B1• Samsung Galaxy Tab (7-inch version)• Samsung Galaxy Tab 7.0 Plus• All devices that maintain the dimensions belowHolder Dimensions:• Minimum Width = 2.25-inch (devices 2.25-inch in width must be a minimum of 7-inch in height to fit)• Maximum Width = 5.75-inch• Depth = 0.875-inchProduct features:• Spring loaded holder expands and contracts for perfect fit of your tablet• Rubber coated tips will hold your tablet firm and stable• Versatility of holder allows for attachment to many RAM-to-RAM ball and 1 inch socket mounts• Socket technology allows for multiple adjustment angles and articulation of your tablet• Easy access grip knobs, located on the back of the holder for quick release of your tabletMaterial: High Strength Composite with Rubber TipsBall Size: 1 Inch Rubber Ball (B-Ball)Colour: blackNore: displayed units are not part of the delivery. Delivery includes X-Grip II cradle only!
SKU
RAM-HOL-UN8BU
Warranty
Quantity
0
Price
€69.09
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A/DB-Sub-Anschluss
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU:Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: 2x USB-A 2.0 & DB9 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PD2-DB9KLU holder is supplied.
SKU
RAM-HOL-HON11PD2-DB9KLU
Warranty
Quantity
0
Price
€280.16
Out of stock
RAM Mounts Form-Fit Holder for Zebra L10
This RAM Mounts Form-Fit holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDU:Compatible with the Zebra tablet accessoiresEasy insertion and removalInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDU holder is supplied.
SKU
RAM-HOL-ZE15PDU
Warranty
Quantity
0
Price
€154.01
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHLU holder is supplied.
SKU
RAM-HOL-ZE25PDHLU
Warranty
Quantity
0
Price
€334.56
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied.
SKU
RAM-HOL-ZE25PHLU
Warranty
Quantity
0
Price
€248.84
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PD2KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PD2KLU holder is supplied.
SKU
RAM-HOL-ZE10PD2KLU
Warranty
Quantity
0
Price
€158.89
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PLU holder is supplied.
SKU
RAM-HOL-ZE22PLU
Warranty
Quantity
0
Price
€187.23
Out of stock
RAM Mounts Form-Fit Holder (Key-locking) for Honeywell RT10
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9KLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalLockable with keyPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9KLU holder is supplied.
SKU
RAM-HOL-HON9KLU
Warranty
Quantity
0
Price
€131.30
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHU holder is supplied.
SKU
RAM-HOL-HON12PHU
Warranty
Quantity
0
Price
€160.23
Out of stock
RAM Mounts GDS EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts GDS EZ-Roll‘r holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-ZE21PDU holder is supplied.
SKU
RAM-GDS-DOCK-ZE21PDU
Warranty
Quantity
0
Price
€148.86
Out of stock
RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10
This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9CLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalLockable with combo-lockingPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9CLU holder is supplied.
SKU
RAM-HOL-HON9CLU
Warranty
Quantity
0
Price
€129.89
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC8300
This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDHU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDHU holder is supplied.
SKU
RAM-HOL-ZE26PDHU
Warranty
Quantity
0
Price
€177.90
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10U holder is supplied.
SKU
RAM-HOL-ZE10U
Warranty
Quantity
0
Price
€76.40
Out of stock
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PDU holder is supplied.
SKU
RAM-GDS-DOCKL-ZE20PDU
Warranty
Quantity
0
Price
€181.41
Out of stock
RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell CT50, CT60 & CT60 XP
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Honeywell CT50, CT60 & CT60 XP.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle and is also charged via USB-A.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON7CLU:Spring-loaded design for easy insertion and removalCharging functionStylus-Pen holderLockable with comboInput Connector: USB-A 2.0Input Cable Length: 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON7CLU holder is supplied.
SKU
RAM-HOL-HON7CLU
Warranty
Quantity
0
Price
€135.19
Out of stock
RAM Mounts Form-Fit Holder for Zebra ET51/56 (10-inch)
This RAM Mounts holder is suitable for Zebra ET5x 10.1“ Series with rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDU holder is supplied.
SKU
RAM-HOL-ZE11PDU
Warranty
Quantity
0
Price
€138.29
Out of stock
RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10
This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PD2CLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PD2CLU holder is supplied.
SKU
RAM-HOL-HON9PD2CLU
Warranty
Quantity
0
Price
€215.03
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET40/45 (10-inch)
This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PNLLU:Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKNLL-ZE21PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PNLLU holder is supplied.
SKU
RAM-HOL-ZE21PNLLU
Warranty
Quantity
2
Price
€138.42
RAM Mounts Form-Fit Holder (Latch) for Getac ZX10
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDU holder is supplied.
SKU
RAM-HOL-GE4PDU
Warranty
Quantity
0
Price
€241.14
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC8300
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PLU:Spring-loaded design for easy insertion and removalCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PLU holder is supplied.
SKU
RAM-HOL-ZE26PLU
Warranty
Quantity
0
Price
€142.42
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC8300
This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDU:Spring-loaded design for easy insertion and removalCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDU holder is supplied.
SKU
RAM-HOL-ZE26PDU
Warranty
Quantity
0
Price
€125.89
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC8300
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHLU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHLU holder is supplied.
SKU
RAM-HOL-ZE26PHLU
Warranty
Quantity
0
Price
€192.18
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PKLU:Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PKLU holder is supplied.
SKU
RAM-HOL-HON11PKLU
Warranty
Quantity
0
Price
€189.63
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra L10
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PD2U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PD2U holder is supplied.
SKU
RAM-HOL-ZE15PD2U
Warranty
Quantity
0
Price
€163.55
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A Connector
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PD2U:Compatible with OEM hand strap Easy insertion and removalCharging functionWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PD2U holder is supplied.
SKU
RAM-HOL-HON11PD2U
Warranty
Quantity
0
Price
€193.38
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & USB-A Connector
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PDU:Compatible with OEM hand strap Easy insertion and removalCharging functionWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PDU holder is supplied.
SKU
RAM-HOL-HON11PDU
Warranty
Quantity
0
Price
€171.35
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC53/58
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC53 & TC58 with or without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-2U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderWith or without Rugged BootCharging functionLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-2U holder is supplied.
SKU
RAM-HOL-ZE17L-2U
Warranty
Quantity
0
Price
€116.97
Out of stock
RAM Mounts X-Grip Clamp for Tablets (9–11 inches)
The RAM MOUNT X-Grip III line of products just got bigger and better. This model is just what you've been looking for to hold your favorite tablet. Just like the devices it was made for, it is everything you need and nothing you don't. Simple to open and close, the spring loaded RAM X-Grip III leaves the outside edge of your tablet almost completely free of annoying obstructions. Soft rubber fingers apply just enough force to keep your tablet in safe and secure. Compatible with a wide range of mounting solutions, your tablet is sure to find a home no matter where your travels take you.The RAM-HOL-UN9U consists of a composite spring loaded holder, expandable grip arms and additional bottom support keeper. Included are extra easy access grip knobs, located on the back of the holder for quick release of your tablet. The X-Grip III expands and contracts for perfect fit of most 9-11 inches tablets with or without sleeves, as well as some smaller tablets. Please verify dimensions of your tablet below for compatibility with the X-Grip III.Compatible Devices (with or without case):• Amazon Kindle Fire HD 8.9-inch• Apple iPad Air / iPad 4 (with lightning connector) / iPad 3 / iPad 2 / iPad 1• Motorola XOOM / XYBOARD 10.1• Microsoft Surface• Samsung Galaxy Tab 8.9 / Galaxy Tab 10.1 (2014 Edition) / Galaxy Tab 10.1 / Galaxy Tab 2 10.1 / Galaxy Tab 3 10.1• Most 10 inches screen tablets, and also all devices that maintain the following dimensions belowX-Grip III min./max. holder dimensions:• Min. Width = 6.25-inch• Max. Width = 8.1-inch• Min. Length = 8.27-inch• Max. Length = 10.25-inch• Max. Depth = 0.875-inchX-Grip III features:• Spring loaded holder expands and contracts for perfect fit of your tablet• Rubber coated tips will hold your tablet firm and stable• Versatility of holder allows for attachment to many 1 inch socket mounts• Socket technology allows for multiple adjustment angles and articulation of your tablet• Easy access grip knobs, located on the back of the holder for quick release of your tablet• Multiple mounting access points on the back of the holder• Additional support keeper at the bottom of the holder• Will not interfere with electronic ports, speakers and cameraConnection: back side prepared for a round base plate (B- or C-Ball, 1 or 1.5 inch)Material: High Strength Composite with Rubber TipsColour: blackNote: displayed units are not part of the delivery. Delivery includes X-Grip III cradle only!
SKU
RAM-HOL-UN9U
Warranty
Quantity
0
Price
€103.57
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4KLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with KeysAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4KLU holder is supplied.
SKU
RAM-HOL-GE4KLU
Warranty
Quantity
0
Price
€187.03
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Getac ZX10
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PD2U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PD2U holder is supplied.
SKU
RAM-HOL-GE4PD2U
Warranty
Quantity
0
Price
€263.61
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX70
This RAM Mounts Form-Fit (key-locking) holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM Vent-Temp can utilize the vehicle's air vents to direct hot or cold air to the Getac ZX70.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3FKLU:Compatible with the Getac Hand Strap & KickstandEasy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-TempLockable with keyAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-GE3FKLU holder is supplied.
SKU
RAM-HOL-GE3FKLU
Warranty
Quantity
3
Price
€130.71
RAM Mounts Form-Fit Holder (key-locking) for Getac ZX70
This RAM Mounts Form-Fit (key-locking) holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NKLU:Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderLockable with keyAdditional information: This holder version will not support the Getac Rotating Hand Strap & Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NKLU holder is supplied.
SKU
RAM-HOL-GE3NKLU
Warranty
Quantity
3
Price
€129.93
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PD2KLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PD2KLU holder is supplied.
SKU
RAM-HOL-GE4PD2KLU
Warranty
Quantity
0
Price
€302.64
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PKLU holder is supplied.
SKU
RAM-HOL-GE4PKLU
Warranty
Quantity
0
Price
€251.81
Out of stock
RAM Mounts Form-Fit Holder (Key-locking) for Honeywell CT60/XP
This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT50, CT60 & CT60 XP.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle and is also charged via USB-A.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON7KLU:Spring-loaded design for easy insertion and removalCharging functionStylus-Pen holderLockable with keyInput Connector: USB-A 2.0Input Cable Length: 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON7KLU holder is supplied.
SKU
RAM-HOL-HON7KLU
Warranty
Quantity
2
Price
€131.64
RAM Mounts Form-Fit Holder for Honeywell CT50, CT60 & CT60 XP
This RAM Mounts Form-Fit holder is suitable for Honeywell CT50, CT60 & CT60 XP.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON7NPU:Spring-loaded design for easy insertion and removalStylus-Pen holderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON7NPU holder is supplied.
SKU
RAM-HOL-HON7NPU
Warranty
Quantity
0
Price
€84.08
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PD2CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PD2CLU holder is supplied.
SKU
RAM-HOL-ZE10PD2CLU
Warranty
Quantity
2
Price
€143.46
RAM Mounts Form-Fit Holder for Zebra ET51/56 (8-inch)
This RAM Mounts holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PD2U:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PD2U holder is supplied.
SKU
RAM-HOL-ZE10PD2U
Warranty
Quantity
2
Price
€144.23
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PD2CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PD2CLU holder is supplied.
SKU
RAM-HOL-ZE11PD2CLU
Warranty
Quantity
0
Price
€151.29
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 10.1“ with rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PU:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PU holder is supplied.
SKU
RAM-HOL-ZE11PU
Warranty
Quantity
0
Price
€113.23
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra L10
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PD2KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PD2KLU holder is supplied.
SKU
RAM-HOL-ZE15PD2KLU
Warranty
Quantity
0
Price
€190.76
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC73/78
This RAM Mounts holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17-NP-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17-NP-1U holder is supplied.
SKU
RAM-HOL-ZE17-NP-1U
Warranty
Quantity
0
Price
€85.54
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC53/58
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC53 & TC58 with or without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-NP-2U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderWith or without Rugged BootLockable with keyAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-NP-2U holder is supplied.
SKU
RAM-HOL-ZE17L-NP-2U
Warranty
Quantity
2
Price
€95.17
RAM Mounts Form-Fit Holder for Zebra TC22/27
This RAM Mounts Form-Fit holder is suitable for Zebra TC22 & TC27 without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable without Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24-1U holder is supplied.
SKU
RAM-HOL-ZE24-1U
Warranty
Quantity
0
Price
€79.19
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDKLU holder is supplied.
SKU
RAM-HOL-ZE11PDKLU
Warranty
Quantity
0
Price
€152.58
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2LU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2LU holder is supplied.
SKU
RAM-HOL-ZE25PD2LU
Warranty
Quantity
0
Price
€273.09
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC8300
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDLU:Spring-loaded design for easy insertion and removalCharging functionLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDLU holder is supplied.
SKU
RAM-HOL-ZE26PDLU
Warranty
Quantity
2
Price
€134.39
RAM Mounts Form-Fit Holder (Latch) for Zebra L10
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15U holder is supplied.
SKU
RAM-HOL-ZE15U
Warranty
Quantity
0
Price
€96.56
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PCLU holder is supplied.
SKU
RAM-HOL-ZE11PCLU
Warranty
Quantity
0
Price
€139.20
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PDCLU holder is supplied.
SKU
RAM-HOL-ZE11PDCLU
Warranty
Quantity
0
Price
€137.96
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDLU holder is supplied.
SKU
RAM-HOL-ZE25PDLU
Warranty
Quantity
0
Price
€262.10
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDU holder is supplied.
SKU
RAM-HOL-ZE25PDU
Warranty
Quantity
4
Price
€237.15
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC73/78
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-NP-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderLockable with keyAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-NP-1U holder is supplied.
SKU
RAM-HOL-ZE17L-NP-1U
Warranty
Quantity
0
Price
€99.72
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC70/75, TC72/77
This RAM Mounts holder is suitable for Zebra TC70, TC72, TC75 & TC77.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE7U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalCharging functionInput connector: 5.5mm DC ConnectorDC to USB-A Cable is includedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE7U holder is supplied.
SKU
RAM-HOL-ZE7U
Warranty
Quantity
0
Price
€94.10
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Case.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PU:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PU holder is supplied.
SKU
RAM-HOL-ZE10PU
Warranty
Quantity
1
Price
€110.66
RAM Mounts Form-Fit Holder for Getac ZX70
This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NU:Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderAdditional information: This holder version will not support the Getac Rotating Hand Strap & Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NU holder is supplied.
SKU
RAM-HOL-GE3NU
Warranty
Quantity
0
Price
€123.34
Out of stock
RAM Mounts Form-Fit Holder (key-Locking) for Zebra L10
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDKLU holder is supplied.
SKU
RAM-HOL-ZE15PDKLU
Warranty
Quantity
0
Price
€178.78
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400
This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PHLU holder is supplied.
SKU
RAM-HOL-ZE32PHLU
Warranty
Quantity
0
Price
€186.88
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PDHU holder is supplied.
SKU
RAM-HOL-ZE25PDHU
Warranty
Quantity
0
Price
€306.79
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHU holder is supplied.
SKU
RAM-HOL-HON12PDHU
Warranty
Quantity
0
Price
€173.98
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PLU holder is supplied.
SKU
RAM-HOL-HON12PLU
Warranty
Quantity
0
Price
€154.20
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PDCLU holder is supplied.
SKU
RAM-HOL-ZE15PDCLU
Warranty
Quantity
0
Price
€171.50
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PKLU holder is supplied.
SKU
RAM-HOL-ZE11PKLU
Warranty
Quantity
0
Price
€128.68
Out of stock
RAM Mounts Form-Fit Holder for Zebra ET51/56 (10-inch)
This RAM Mounts holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PD2U:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PD2U holder is supplied.
SKU
RAM-HOL-ZE11PD2U
Warranty
Quantity
0
Price
€130.39
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDU holder is supplied.
SKU
RAM-HOL-HON12PDU
Warranty
Quantity
0
Price
€133.45
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2U:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PD2U holder is supplied.
SKU
RAM-HOL-ZE22PD2U
Warranty
Quantity
0
Price
€224.36
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC8300
This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHU:Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHU holder is supplied.
SKU
RAM-HOL-ZE26PHU
Warranty
Quantity
0
Price
€165.33
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5 mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PCLU holder is supplied.
SKU
RAM-HOL-ZE10PCLU
Warranty
Quantity
0
Price
€130.43
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400
This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PLU holder is supplied.
SKU
RAM-HOL-ZE32PLU
Warranty
Quantity
0
Price
€152.36
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Getac ZX10
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorInput Voltage: 19VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PU holder is supplied.
SKU
RAM-HOL-GE4PU
Warranty
Quantity
0
Price
€223.78
Out of stock
RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10
This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PCLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PCLU holder is supplied.
SKU
RAM-HOL-HON9PCLU
Warranty
Quantity
0
Price
€180.88
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDLU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PDLU holder is supplied.
SKU
RAM-HOL-ZE22PDLU
Warranty
Quantity
0
Price
€230.45
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PKLU holder is supplied.
SKU
RAM-HOL-ZE10PKLU
Warranty
Quantity
0
Price
€140.71
Out of stock
RAM Mounts Holder for Zebra MC9300/9400
This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32U:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32U holder is supplied.
SKU
RAM-HOL-ZE32U
Warranty
Quantity
0
Price
€94.27
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11PD2KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11PD2KLU holder is supplied.
SKU
RAM-HOL-ZE11PD2KLU
Warranty
Quantity
0
Price
€162.81
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PLU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with KeysInput Connector: USB-A Input Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PLU holder is supplied.
SKU
RAM-HOL-ZE24PLU
Warranty
Quantity
0
Price
€122.41
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PCLU holder is supplied.
SKU
RAM-HOL-ZE15PCLU
Warranty
Quantity
0
Price
€155.83
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with rugged case.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PDU:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PDU holder is supplied.
SKU
RAM-HOL-ZE10PDU
Warranty
Quantity
0
Price
€131.53
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET80/85
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22LU:Compatible with accessoriesEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right or NFC-RepeaterAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22LU holder is supplied.
SKU
RAM-HOL-ZE22LU
Warranty
Quantity
0
Price
€145.31
Out of stock
RAM Mounts Form-Fit Holder for Zebra MC9300/9400
This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PHU holder is supplied.
SKU
RAM-HOL-ZE32PHU
Warranty
Quantity
0
Price
€161.13
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC22/27
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PL-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with keyInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PL-1U holder is supplied.
SKU
RAM-HOL-ZE24PL-1U
Warranty
Quantity
0
Price
€128.82
Out of stock
RAM Mounts Form-Fit Holder (Combo-locking) for Honeywell RT10
This RAM Mounts Form Fit (combo-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDCLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with comboPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDCLU holder is supplied.
SKU
RAM-HOL-HON9PDCLU
Warranty
Quantity
0
Price
€195.20
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15CLU holder is supplied.
SKU
RAM-HOL-ZE15CLU
Warranty
Quantity
0
Price
€104.56
Out of stock
RAM Mounts Form-Fit Holder for Zebra ET60/65
This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2HU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2HU holder is supplied.
SKU
RAM-HOL-ZE25PD2HU
Warranty
Quantity
0
Price
€311.53
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Getac ZX10
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4U holder is supplied.
SKU
RAM-HOL-GE4U
Warranty
Quantity
0
Price
€158.00
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, FCC, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCK-ZE20PD2U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PD2U holder is supplied.
SKU
RAM-HOL-ZE20PD2U
Warranty
Quantity
13
Price
€167.09
RAM Mounts Form-Fit Holder for Getac ZX70
This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM Vent-Temp can utilize the vehicle's air vents to direct hot or cold air to the Getac ZX70.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3FU:Compatible with the Getac tablet accessoiresEasy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-TempAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-GE3FU holder is supplied.
SKU
RAM-HOL-GE3FU
Warranty
Quantity
0
Price
€124.32
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PHLU holder is supplied.
SKU
RAM-HOL-HON12PHLU
Warranty
Quantity
0
Price
€212.85
Out of stock
RAM Mounts Form-Fit Holder for Zebra MC9300/9400
This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDU holder is supplied.
SKU
RAM-HOL-ZE32PDU
Warranty
Quantity
0
Price
€140.98
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderLockable with keyInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PLU holder is supplied.
SKU
RAM-HOL-ZE25PLU
Warranty
Quantity
2
Price
€209.93
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10CLU holder is supplied.
SKU
RAM-HOL-ZE10CLU
Warranty
Quantity
0
Price
€125.38
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU:Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25LU holder is supplied.
SKU
RAM-HOL-ZE25LU
Warranty
Quantity
0
Price
€156.49
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10KLU holder is supplied.
SKU
RAM-HOL-ZE10KLU
Warranty
Quantity
0
Price
€101.62
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PDKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keyInput Connector: 5.5 mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PDKLU holder is supplied.
SKU
RAM-HOL-ZE10PDKLU
Warranty
Quantity
0
Price
€139.19
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET5x 10.1“ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11KLU holder is supplied.
SKU
RAM-HOL-ZE11KLU
Warranty
Quantity
0
Price
€103.69
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET40/45 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE20PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PDKLU holder is supplied.
SKU
RAM-HOL-ZE20PDKLU
Warranty
Quantity
0
Price
€145.38
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET40/45 (8-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PD2KLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE20PD2U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PD2KLU holder is supplied.
SKU
RAM-HOL-ZE20PD2KLU
Warranty
Quantity
8
Price
€210.03
RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDU holder is supplied.
SKU
RAM-HOL-HON9PDU
Warranty
Quantity
0
Price
€175.44
Out of stock
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (8-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE20C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE20PD2U holder is supplied.
SKU
RAM-GDS-DOCKL-ZE20PD2U
Warranty
Quantity
0
Price
€191.63
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX10
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder will not support the Getac hand strap accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE4PDKLU holder is supplied.
SKU
RAM-HOL-GE4PDKLU
Warranty
Quantity
0
Price
€267.14
Out of stock
RAM Mounts EZ-Roll’r Holder (key-locking) for Zebra ET40/45 (8-inch)
This RAM Mounts EZ-Roll‘r (key-locking) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PKLU holder is supplied.
SKU
RAM-HOL-ZE20PKLU
Warranty
Quantity
0
Price
€143.56
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDHLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionHeated Pogo-PinsLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDHLU holder is supplied.
SKU
RAM-HOL-HON12PDHLU
Warranty
Quantity
0
Price
€203.91
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (8-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 8.3“ & 8.4“ Series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE10PDCLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingInput Connector: 5.5 mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE10PDCLU holder is supplied.
SKU
RAM-HOL-ZE10PDCLU
Warranty
Quantity
0
Price
€130.50
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra ET5x 10.1“ Series with rugged boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalPrepared for mounting additional devices such as handheldsLockable with combo-lockingAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11CLU holder is supplied.
SKU
RAM-HOL-ZE11CLU
Warranty
Quantity
0
Price
€93.61
Out of stock
RAM Mounts Form-Fit Holder (with key-locking) for Honeywell RT10
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PDKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PDKLU holder is supplied.
SKU
RAM-HOL-HON9PDKLU
Warranty
Quantity
0
Price
€211.23
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra MC9300/9400
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDHLU holder is supplied.
SKU
RAM-HOL-ZE32PDHLU
Warranty
Quantity
0
Price
€201.64
Out of stock
RAM Mounts Form-Fit Holder (Key-locking) for Honeywell RT10
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PKLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PKLU holder is supplied.
SKU
RAM-HOL-HON9PKLU
Warranty
Quantity
0
Price
€190.79
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra L10
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PKLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keysInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PKLU holder is supplied.
SKU
RAM-HOL-ZE15PKLU
Warranty
Quantity
0
Price
€162.56
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra L10
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra XSLATE L10.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15KLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with keysAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15KLU holder is supplied.
SKU
RAM-HOL-ZE15KLU
Warranty
Quantity
0
Price
€112.35
Out of stock
RAM Mounts Form-Fit Holder for Zebra MC9300/9400
This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDHU holder is supplied.
SKU
RAM-HOL-ZE32PDHU
Warranty
Quantity
0
Price
€175.69
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC73/78
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-1U holder is supplied.
SKU
RAM-HOL-ZE17L-1U
Warranty
Quantity
0
Price
€120.84
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsInput Voltage: 12VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PD2U holder is supplied.
SKU
RAM-HOL-ZE25PD2U
Warranty
Quantity
0
Price
€247.00
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra MC9300/9400
This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDLU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDLU holder is supplied.
SKU
RAM-HOL-ZE32PDLU
Warranty
Quantity
0
Price
€170.85
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC22/27
This RAM Mounts Form-Fit holder is suitable for Zebra TC22 & TC27 with Rugged Case.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24U holder is supplied.
SKU
RAM-HOL-ZE24U
Warranty
Quantity
0
Price
€71.74
Out of stock
RAM Mounts GDS Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10-inch)
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10“ series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveLockable with KeysInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To use the holder you need the RAM-GDS-SKIN-ZE21C-NG protective sleeve.Devices shown are not included in the delivery.Only the RAM-GDS-DOCKL-ZE21PDU holder is supplied.
SKU
RAM-GDS-DOCKL-ZE21PDU
Warranty
Quantity
0
Price
€187.63
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PU holder is supplied.
SKU
RAM-HOL-HON9PU
Warranty
Quantity
0
Price
€156.64
Out of stock
RAM Mounts Form-Fit Holder (Combo-Locking) for Zebra L10
This RAM Mounts Form-Fit (combo-locking) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PD2CLU:Compatible with the Zebra tablet accessoiresEasy insertion and removalLockable with combo-lockingInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transfer Speed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PD2CLU holder is supplied.
SKU
RAM-HOL-ZE15PD2CLU
Warranty
Quantity
0
Price
€184.10
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCK-ZE20PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PDU holder is supplied.
SKU
RAM-HOL-ZE20PDU
Warranty
Quantity
0
Price
€125.21
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET40 & ET45 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged BootInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Frame, see RAP-INSERT-ZE21U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PU holder is supplied.
SKU
RAM-HOL-ZE21PU
Warranty
Quantity
0
Price
€123.69
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET40/45 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET40 & ET45 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged BootLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Frame, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE21PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PKLU holder is supplied.
SKU
RAM-HOL-ZE21PKLU
Warranty
Quantity
0
Price
€148.80
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (8-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20U.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PU holder is supplied.
SKU
RAM-HOL-ZE20PU
Warranty
Quantity
0
Price
€115.55
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET40/45 (8-inch)
This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 8“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PNLLU:Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE20LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKNLL-ZE20PU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE20PNLLU holder is supplied.
SKU
RAM-HOL-ZE20PNLLU
Warranty
Quantity
0
Price
€132.14
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5KLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with KeysAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5KLU holder is supplied.
SKU
RAM-HOL-GE5KLU
Warranty
Quantity
0
Price
€215.53
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC & Dual USB-A Connector
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PD2KLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Input Voltage: 19VOutput Voltage: 14VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5PD2KLU holder is supplied.
SKU
RAM-HOL-GE5PD2KLU
Warranty
Quantity
0
Price
€351.23
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC & Dual USB-A Connector
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PD2U:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Input Voltage: 19VOutput Voltage: 14VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5PD2U holder is supplied.
SKU
RAM-HOL-GE5PD2U
Warranty
Quantity
0
Price
€323.39
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC & USB-A Connector
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PDKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VOutput Voltage: 14VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5PDKLU holder is supplied.
SKU
RAM-HOL-GE5PDKLU
Warranty
Quantity
0
Price
€329.03
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Getac ZX80 Rugged Tablet - 5.5mm DC & USB-A Connector
This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PDU:Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-ConnectorOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Input Voltage: 19VOutput Voltage: 14VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5PDU holder is supplied.
SKU
RAM-HOL-GE5PDU
Warranty
Quantity
0
Price
€301.80
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Getac ZX80 Rugged Tablet - 5.5mm DC Power Supply
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PKLU:Compatible with the Getac tablet accessoiresNot compatible with the Getac 4-point hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp, Temp Right or NFC repeaterInput Connector: 5.5mm DC-BuchseInput Voltage: 19VOutput Voltage: 14VInput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, WEEE & RoHSAdditional information: This holder is compatible with the Getac 2-point hand strap, but will not support the 4-point hand strap.Devices shown are not included in the delivery.Only the RAM-HOL-GE5PKLU holder is supplied.
SKU
RAM-HOL-GE5PKLU
Warranty
Quantity
0
Price
€304.23
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A/DB-Sub Connector
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PD2-DB9U:Compatible with OEM hand strap Easy insertion and removalCharging functionWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: 2x USB-A 2.0 & DB9 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PD2-DB9U holder is supplied.
SKU
RAM-HOL-HON11PD2-DB9U
Warranty
Quantity
0
Price
€250.68
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & Dual USB-A Connector
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PD2KLU:Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PD2KLU holder is supplied.
SKU
RAM-HOL-HON11PD2KLU
Warranty
Quantity
0
Price
€225.68
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC & USB-A Connector
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PDKLU:Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PDKLU holder is supplied.
SKU
RAM-HOL-HON11PDKLU
Warranty
Quantity
0
Price
€201.35
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot - 5.5mm DC Power Supply
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PU:Compatible with OEM hand strap Easy insertion and removalCharging functionWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VInput Cable Length: ca. 100 cmCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11PU holder is supplied.
SKU
RAM-HOL-HON11PU
Warranty
Quantity
2
Price
€158.48
RAM Mounts Form-Fit Holder (Latch) for Honeywell ScanPal EDA10A Tablet in OEM Protective Boot
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11U:Compatible with OEM hand strap Easy insertion and removalWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesCertifications: RoHS, WEEE, CE & FCCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON11U holder is supplied.
SKU
RAM-HOL-HON11U
Warranty
Quantity
0
Price
€133.98
Out of stock
RAM Mounts Form-Fit Holder (Key-Locking) for Samsung Tab Active Pro & Active4 Pro - in OEM/RAM Sleeve - USB-C Power Supply
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Samsung Tab Active Pro and Active4 Pro Tablet in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM57CPKLU:Compatible with GDS hand-standCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information: This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM57CPKLU holder is supplied.
SKU
RAM-HOL-SAM57CPKLU
Warranty
Quantity
0
Price
€145.00
Out of stock
RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector
This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPT-CAU:Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28-inch depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalWith LatchCharging functionInput Connector: USB-COutput Connector: USB-C & USB-A (Peripheral output - 900mAh per Port)Transfer-Speed: 480MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPT-CAU holder is supplied.
SKU
RAM-HOL-SAM58CPT-CAU
Warranty
Quantity
0
Price
€151.68
Out of stock
RAM Mounts EZ-Roll'r Modular Holder for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector
This RAM Mounts EZ-Roll’r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-StandThe back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CPN-CAU:Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-COutput Connector: USB-C & USB-A (Peripheral output - 900mAh per Port)Transfer-Speed: 12MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM60CPN-CAU holder is supplied.
SKU
RAM-HOL-SAM60CPN-CAU
Warranty
Quantity
0
Price
€133.46
Out of stock
RAM Mounts EZ-Roll'r Holder for Samsung Tab Active3 - In OtterBox uniVERSE Case- USB-C Connector
This RAM Mounts EZ-Roll‘r Form-Fit holder is suitable for Samsung Tab Active3 in an OtterBox uniVERSE case.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CP-OT1U:Compatible with accessoriesCan only be used with OtterBox uniVERSE caseAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM60CP-OT1U holder is supplied.
SKU
RAM-HOL-SAM60CP-OT1U
Warranty
Quantity
0
Price
€95.63
Out of stock
RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-C/A Connector
This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C and USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLN-CAU:Compatible with accessories and side accessory attachmentsCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-COutput Connector: USB-C & USB-A (Peripheral output - 900mAh per Port)Transfer-Speed: 480MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLN-CAU holder is supplied.
SKU
RAM-HOL-SAM58CPKLN-CAU
Warranty
Quantity
0
Price
€179.70
Out of stock
RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Power & Data Connector
This RAM Mounts Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-StandThe back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLN-CU:Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-COutput Connector: USB-C (Peripheral output - 500mAh)Transfer-Speed: 480MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLN-CU holder is supplied.
SKU
RAM-HOL-SAM58CPKLN-CU
Warranty
Quantity
0
Price
€165.24
Out of stock
RAM Mounts Form- Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.The included RAM NFC extender supports the NFC function with a range of up to 30 cm.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, GDS Roto-Mag and side accessory attachments.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKL-NFCU:Compatible with accessoriesIncluding RAM NFC-ExtenderCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Potential interference of NFC functionality may occur when positioned close to strong magnets.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKL-NFCU holder is supplied.
SKU
RAM-HOL-SAM58CPKL-NFCU
Warranty
Quantity
0
Price
€223.58
Out of stock
RAM Mounts Modular Form-Fit Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector
This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLNU:Compatible with accessories and side accessory attachmentsCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information:This product will not support the -inchNo Battery Mode-inch function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLNU holder is supplied.
SKU
RAM-HOL-SAM58CPKLNU
Warranty
Quantity
0
Price
€142.08
Out of stock
RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector
This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU:Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28-inch depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalLockable with keyCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Transfer-Speed: 12MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLT-AU holder is supplied.
SKU
RAM-HOL-SAM58CPKLT-AU
Warranty
Quantity
0
Price
€162.53
Out of stock
RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & Dual USB-A & RJ45(Ethernet) Connector
This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral & data support is provided by the built-in dual USB-A & RJ45 (ethernet) cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLT-RJ45AU:Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28-inch depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalLockable with keyCharging functionInput Connector: USB-COutput Connector: USB-A & RJ45 (Peripheral output - 900mAh per Port)Transfer-Speed: 480MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLT-RJ45AU holder is supplied.
SKU
RAM-HOL-SAM58CPKLT-RJ45AU
Warranty
Quantity
0
Price
€220.88
Out of stock
RAM Mounts Form-Fit Low Profile Holder (Key-Locking) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C Connector
This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLTU:Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28-inch depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalLockable with keyCharging functionInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information:This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPKLTU holder is supplied.
SKU
RAM-HOL-SAM58CPKLTU
Warranty
Quantity
0
Price
€150.38
Out of stock
RAM Mounts Form-Fit Low Profile Holder (Latch) for Samsung Tab Active3 & Active5 - In OEM/RAM Sleeve - USB-C & USB-A Connector
This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPT-1AU:Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28-inch depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalWith LatchCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)Transfer-Speed: 12MbpsInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information:This dock is not compatible with the GDS Hand-Stand, RAM Temp-Right, or GDS Roto-Mag.Devices shown are not included in the delivery.Only the RAM-HOL-SAM58CPT-1AU holder is supplied.
SKU
RAM-HOL-SAM58CPT-1AU
Warranty
Quantity
0
Price
€140.16
Out of stock
RAM Mounts X-Grip Holder for Smartphones - Up to 114.3 mm Width - With B-Ball (1“)
The RAM Mounts X-Grip Universal Holder is a rugged and versatile solution for securely mounting smartphones of various sizes.Rubber-coated end caps provide additional protection and a firm grip.This holder is ideal for use on motorcycles, bicycles, in cars, boats, or other mobile applications.The included tether offers extra security in especially demanding environments such as off-road rides.Thanks to its open design, all buttons, ports, and the camera remain fully accessible.The X-Grip is compatible with a wide range of RAM Mounts components and can be easily integrated into existing mounting systems.Thanks to the integrated spring mechanism, the device can be inserted and removed quickly and easily.The back of the X-Grip is prepared with a Ball (B-Size).Product features RAM Mounts RAM-HOL-UN10BU:Universal fit for many smartphonesSecure gripQuick insertion and removalFull access to ports and cameraIncludes safety tetherWeight capacity for standard use up to 0.91 kgWeight capacity for heavy-duty use up to 0.45 kgCompatible with smartphones with the following dimensions:Minimum width: 44.45 mmMaximum width: 114.3 mmMaximum depth: 22.225 mmAdditional information: Exposure to vibrations, such as those produced by high-performance motorcycles, may affect the functionality of iPhone cameras.Devices shown are not included in the delivery.Only the RAM-HOL-UN10BU holder is supplied.
SKU
RAM-HOL-UN10BU
Warranty
Quantity
0
Price
€61.06
Out of stock
RAM Mounts X-Grip Tablet Clamp for Tablets (12–13 inches)
The new RAM X-Grip line of products just got bigger and better. This model - RAM-HOL-UN11U - is just what you've been looking for to hold your favorite tablet. Just like the devices it was made for, it is everything you need and nothing you don't. Simple to open and close, the spring loaded RAM X-Grip leaves the outside edge of your tablet almost completely free of annoying obstructions. Soft rubber fingers apply just enough force to keep your tablet in safe and secure. Compatible with a wide range of mounting solutions, your tablet is sure to find a home no matter where your travels take you.The RAM-HOL-UN11U holder expands and contracts for perfect fit of most 12” and 13-inch tablets with or without sleeves, as well as some smaller tablets. This holder by RAM consists of a composite spring loaded holder, expandable grip arms and additional bottom support keeper.Compatible Devices (with or without case):• Microsoft Surface Pro 3• Samsung Galaxy Note Pro 12.2• Most 12-inch Screen Tablets• All Tablets meeting the holder dimensions belowX-Grip V Holder Dimensions:• Minimum Width = 7.25-inch• Maximum Width = 8.75-inch• Maximum Length (without additional supports) = unlimited• Maximum Length (with additional supports) = 10.25-inch• Depth = 0.875-inchX-Grip V holder features:• Spring loaded cradle expands and contracts for perfect fit of your tablet• Rubber coated tips will hold your tablet firm and stable• Versatility of cradle allows for attachment to many 1-inch socket mounts• Socket technology allows for multiple adjustment angles and articulation of your tablet• Easy access grip knobs, located on the back of the cradle for quick release of your tablet• Multiple mounting access points on the back of the cradle• Additional support keeper at the bottom of the cradle• Full access to all ports• Backside prepared to connect to round base plates (B- or C-Ball size)Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components, High Strength Composite, Rubber TipsColor: blackNote: displayed units are not part of the delivery. Delivery includes X-Grip V cradle - RAM-HOL-UN11U - only!
SKU
RAM-HOL-UN11U
Warranty
Quantity
0
Price
€113.42
Out of stock
RAM Mounts X-Grip Clamp for Smartphones up to 82.6 mm wide
Sometimes, its all about the design. If you are looking for a compact mount for your cell phone without that cookie cutter shape, you've found it. The RAM MOUNT X-Grip has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the RAM MOUNT X-Grip is the cell phone holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your phone and become the most useful accessory in your vehicle.Compatible Devices:• Apple iPhone 6 with or without bumper, skin or case• Apple iPhone 5S / 5C with or without bumper, skin or case• Apple iPhone 4S / 4 with or without bumper, skin or case• Apple iPhone 3G / 3 with or without bumper, skin or case• Apple iPhone (1st Generation)• Apple iPod Touch (all models)• Apple iPod (G1-G5)• All devices that maintain the holder dimensions belowHolder Dimensions:• Minimum Width = 0.875-inch (devices at 0.875-inch must be a minimum of 4-inch in height to fit into holder)• Maximum Width = 3.25-inch• Depth = 0.875-inchFeatures:• Spring loaded holder expands and contracts for perfect fit of your device• Rubber coated tips will hold device firm and stable• Versatility of holder allows for attachment to many RAM-to-RAM ball mounts• Single socket technology allows for multiple adjustment angles and articulation of deviceMaterial: High Strength Composite with Rubber TipsBall Size: 1 Inch Rubber Ball (B-Ball)Colour: blackWeight: n/aNote: displayed devices are not part of the delivery. Delivery includes RAM MOUNT X-Grip Clamp - RAM-HOL-UN7BU - only!
SKU
RAM-HOL-UN7BU
Warranty
Quantity
0
Price
€55.16
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET51/56 (10-inch)
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET5x 10.1“.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE11U:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE11U holder is supplied.
SKU
RAM-HOL-ZE11U
Warranty
Quantity
0
Price
€84.64
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC21/26
This RAM Mounts Form-Fit holder is suitable for Zebra TC21 & TC26.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE14U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalCharging functionInput connector: USB-A (female)Input cable length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE14U holder is supplied.
SKU
RAM-HOL-ZE14U
Warranty
Quantity
0
Price
€90.61
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC73/78
This RAM Mounts holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17-1U holder is supplied.
SKU
RAM-HOL-ZE17-1U
Warranty
Quantity
0
Price
€116.61
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC53/TC58
This RAM Mounts holder is suitable for Zebra TC53 & TC58 with or without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17-NP-2U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderFits with or without Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17-NP-2U holder is supplied.
SKU
RAM-HOL-ZE17-NP-2U
Warranty
Quantity
0
Price
€78.40
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC53/58
This RAM Mounts holder is suitable for Zebra TC53 & TC58.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17-2U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17-2U holder is supplied.
SKU
RAM-HOL-ZE17-2U
Warranty
Quantity
0
Price
€108.33
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET80/85
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PD2LU:Compatible with accessoriesEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right or NFC-RepeaterLockable with keyInput Connector: 5.5mm DCOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PD2LU holder is supplied.
SKU
RAM-HOL-ZE22PD2LU
Warranty
Quantity
0
Price
€254.05
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET80/85
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PDU:Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp- Right or NFC-RepeaterInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE22PDU holder is supplied.
SKU
RAM-HOL-ZE22PDU
Warranty
Quantity
0
Price
€201.10
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC22/27
This RAM Mounts Form-Fit holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PU holder is supplied.
SKU
RAM-HOL-ZE24PU
Warranty
Quantity
0
Price
€90.25
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC22/27
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24L-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockLockable with keyOnly usable without Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24L-1U holder is supplied.
SKU
RAM-HOL-ZE24L-1U
Warranty
Quantity
0
Price
€130.62
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra TC22/27
This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24LU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalLockable with keyIntegrated stylus holder on the side of the dockOnly usable with Rugged BootAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24LU holder is supplied.
SKU
RAM-HOL-ZE24LU
Warranty
Quantity
0
Price
€92.09
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC22/27
This RAM Mounts Form-Fit holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24P-1U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable without Rugged BootInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24P-1U holder is supplied.
SKU
RAM-HOL-ZE24P-1U
Warranty
Quantity
0
Price
€96.60
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHU holder is supplied.
SKU
RAM-HOL-ZE25PHU
Warranty
Quantity
0
Price
€221.56
Out of stock
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PU:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: ca. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PU holder is supplied.
SKU
RAM-HOL-ZE25PU
Warranty
Quantity
20
Price
€184.36
RAM Mounts Form-Fit Holder (Latch) for Zebra ET60/65
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25U:Compatible with Zebra KeyboardEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp Right, NFC-Repeater or Zebra CAC ReaderAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25U holder is supplied.
SKU
RAM-HOL-ZE25U
Warranty
Quantity
0
Price
€128.19
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC8300
This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PU:Spring-loaded design for easy insertion and removalCharging functionInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable length: ca. 100 cmCertification: FSS, CE, RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PU holder is supplied.
SKU
RAM-HOL-ZE26PU
Warranty
Quantity
1
Price
€111.32
RAM Mounts Quick Release Holder for Zebra ZQ320 Series
This RAM Mounts Quick-Release holder is suitable for Zebra ZQ320 Series.This holder is not compatible with the printer accessories for the Zebra ZQ320 series.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE27U:Quick-Release for easy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE27U holder is supplied.
SKU
RAM-HOL-ZE27U
Warranty
Quantity
3
Price
€31.08
RAM Mounts Quick Release Holder for Zebra ZQ310 Series
This RAM Mounts Quick-Release holder is suitable for Zebra ZQ310 Series.This holder is not compatible with the printer accessories for the Zebra ZQ310 series.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE28U:Quick-Release for easy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE28U holder is supplied.
SKU
RAM-HOL-ZE28U
Warranty
Quantity
2
Price
€30.58
RAM Mounts Quick Release Holder for Zebra ZQ511 Series
This RAM Mounts Quick-Release holder is suitable for Zebra ZQ511 Series.This holder is not compatible with the printer accessories for the Zebra ZQ511 series.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE29U:Quick-Release for easy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE29U holder is supplied.
SKU
RAM-HOL-ZE29U
Warranty
Quantity
0
Price
€28.60
Out of stock
RAM Mounts Quick Release Holder for Zebra ZQ521 Series
This RAM Mounts Quick-Release holder is suitable for Zebra ZQ521 Series.This holder is not compatible with the printer accessories for the Zebra ZQ521 series.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE30U:Quick-Release for easy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE30U holder is supplied.
SKU
RAM-HOL-ZE30U
Warranty
Quantity
0
Price
€34.90
Out of stock
RAM Mounts Form-Fit Holder for Zebra MC9300/9400
This RAM Mounts spring loaded holder is suitable for Zebra MC9400 & MC9300 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PU:Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC, CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PU holder is supplied.
SKU
RAM-HOL-ZE32PU
Warranty
Quantity
0
Price
€125.59
Out of stock
RAM Mounts holder for Zebra MC3300/3400/3450
This RAM Mounts form-fit holder is suitable for Zebra MC3300/3400/3450 with or without rugged boot. To insert the device, press the upper part of the holder with the device facing upwards and insert the appropriate device.Thanks to the spring-loaded design, the device sits firmly and securely in the holder.The back of the device holder is designed to accommodate a round base plate (not included).Product features RAM Mounts RAM-HOL-ZE33PUSpring-loaded design for easy insertion and removalScanning function possible in holderAdditional note: Devices shown are not included in delivery.Only the RAM-HOL-ZE33PU holder is supplied.
SKU
RAM-HOL-ZE33PU
Warranty
Quantity
0
Price
€104.56
Out of stock
RAM Mounts Form-Fit Holder for Zebra TC51/56, TC52/57
This RAM Mounts holder is suitable for Zebra TC51, TC52, TC56 & TC57 with or without rugged case.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via USB-A.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE6U:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalCharging functionInput connector: USB-A (male)Input cable length: ca. 100 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE6U holder is supplied.
SKU
RAM-HOL-ZE6U
Warranty
Quantity
0
Price
€101.61
Out of stock
RAM Mounts Quick-Draw Form-Fit Holder for Zebra TC8300
This RAM Mounts Quick-Draw Form-Fit holder is suitable for Zebra TC8000 & TC8300.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE9U:Spring-loaded design for easy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE9U holder is supplied.
SKU
RAM-HOL-ZE9U
Warranty
Quantity
0
Price
€45.80
Out of stock
RAM Mounts Form-Fit Holder for Honeywell CT50, CT60 & CT60 XP
This RAM Mounts Form-Fit holder is suitable for Honeywell CT50, CT60 & CT60 XP.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle and is also charged via USB-A.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON7U:Spring-loaded design for easy insertion and removalCharging functionStylus-Pen holderInput Connector: USB-A 2.0Input Cable Length: 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON7U holder is supplied.
SKU
RAM-HOL-HON7U
Warranty
Quantity
2
Price
€112.40
RAM Mounts Form-Fit Holder (Latch) for Zebra L10
This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra XSLATE L10.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a scanner, hand strap or PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE15PU:Compatible with the Zebra tablet accessoiresEasy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DCAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE15PU holder is supplied.
SKU
RAM-HOL-ZE15PU
Warranty
Quantity
3
Price
€136.69
RAM Mounts Form-Fit Holder (key-locking) for Honeywell CT40, CT45 & CT47
This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDLU:Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bootCompatible with OEM hand strapInput Connector: 5.5mm DC-ConnectorInput Voltage: 5VOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transferspeed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 100 cmCertifications: FCC, IC, CE, UKCA, RoHS & WEEEAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON12PDLU holder is supplied.
SKU
RAM-HOL-HON12PDLU
Warranty
Quantity
3
Price
€191.19
RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PD2U:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionWith LatchPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PD2U holder is supplied.
SKU
RAM-HOL-HON9PD2U
Warranty
Quantity
3
Price
€187.18
RAM Mounts Form-Fit Holder for Zebra EC50/55
This RAM Mounts Form-Fit holder is suitable for Zebra EC50 & EC55.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC50 & EC55 secure, the powered dock also leaves the device’s top scanner, buttons and camera exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE16U:Spring-loaded design for easy insertion and removalCharging functionInput connector: USB-A (female)Input cable length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE16U holder is supplied.
SKU
RAM-HOL-ZE16U
Warranty
Quantity
3
Price
€94.47
RAM Mounts Form-Fit Holder (Key-Locking) for Zebra TC70/75, TC72/77
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC70, TC72, TC75 & TC77.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE7LU:Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalLockable with KeysCharging functionInput connector: 5.5mm DCDC to USB-A Cable is includedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE7LU holder is supplied.
SKU
RAM-HOL-ZE7LU
Warranty
Quantity
1
Price
€119.81
RAM Mounts Power-Grip XL Universal holder for Scanners - Composite - 4-Hole AMPS - Screw-Set
The RAM Mounts Power-Grip XL Universal Holder for larger industrial Scanners is the ideal solution for warehouses, logistics, and retail.The robust cradle is compatible with a wide range of industrial scanners.The open-bottom design allows scanning while the scanner remains in the holder.Replaceable elastomeric fins grip the handle securely, ensure a tight fit, and can be easily replaced when needed.The back side is prepared for attaching a round base plate (AMPS hole pattern - not included).Alternatively, the bottom side is also prepared for a rectangular base plate (2” x 3” plate- not included).Product features RAM Mounts RAP-450U:Universal fit for many scannersSecure holdQuick insertion and removalOpen-bottom design allows scanning while in the cradleIntegrated holes for shoulder strapsReplaceable elastomeric finsInternal Cradle Dimensions:Length: 67.56 mmWidth: 100.58 mmDepth: 188.72 mmAdditional information: Devices shown are not included in the delivery.Only the RAP-450U holder is supplied.
SKU
RAP-450U
Warranty
Quantity
0
Price
€70.60
Out of stock
RAM® Printer Mount with Paper Feed for Zebra ZQ630 Series
RAM® Printer Mount with Paper Feed for Zebra ZQ630 Series
SKU
RAM-PM1-ZE31U
Warranty
Quantity
49
Price
€108.84
RAM Mounts Form-Fit Holder (Latch) for Honeywell RT10
This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell RT10 Rugged Tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9U:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalWith LatchPrepared for mounting additional devices such as handheldsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9U holder is supplied.
SKU
RAM-HOL-HON9U
Warranty
Quantity
0
Price
€104.69
Out of stock
RAM Mounts Form-Fit Holder (Key-locking) for Honeywell RT10
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell RT10 Rugged Tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as a hand strap or extended battery pack can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON9PD2KLU:Compatible with accessories e.g. hand strap or extended battery Easy insertion and removalCharging functionLockable with keyPrepared for mounting additional devices such as handheldsInput Connector: 5.5mm DC-ConnectorOutput Connector: 2x USB-A 2.0 (Peripheral output - 900mAh per Port)Transferspeed: 12MbpsAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-HON9PD2KLU holder is supplied.
SKU
RAM-HOL-HON9PD2KLU
Warranty
Quantity
0
Price
€231.23
Out of stock
RAM Mounts Tab-Tite Universal Holder for 10 - 11” Rugged Tablets
This RAM Mounts Tab-Tite™ universal cradle is suitable for Panasonic Toughpad FZ-G1 and most 10-inch - 11-inch rugged tablets. To insert the device, pull the upper part of the cradle apart, insert the appropriate tablet and carefully release the upper end. The spring-loaded design holds the tablet tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).The Tab-Tite™ holder is compatible with most tablets within the dimensions listed.Product features RAM Mounts Tab-Tite™ holder (RAM-HOL-TAB19U):Open Cup design for different tablet sizesSpring-loaded design for easy insertion and removalFull access to all device interfaces on most modelsCompatible for tablets with the following dimensions:Height: 273,05 mm up to 339,72 mmWidth: 165,1 mm up to 196,85 mmDepth: 3,3 mm up to 23,62 mmAdditional information: Devices shown are not included in the delivery.Only the Tab-Tite™ holder (RAM-HOL-TAB19U) is supplied.
SKU
RAM-HOL-TAB19U
Warranty
Quantity
0
Price
€54.76
Out of stock
RAM Mounts Form-Fit Holder (key-locking) for Zebra ET40/45 (10-inch)
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PDKLU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional information: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21LU.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCKL-ZE21PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PDKLU holder is supplied.
SKU
RAM-HOL-ZE21PDKLU
Warranty
Quantity
0
Price
€150.84
Out of stock
RAM Mounts EZ-Roll'r Holder for Zebra ET40/45 (10-inch)
This RAM Mounts EZ-Roll‘r holder is suitable for Zebra ET40 & ET45 10“ series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PDU:Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500mAh)Transfer Speed: 12MbpsInput Cable Length: ca. 100 cmOutput Cable Length: ca. 24 cmCertifications: RoHS, WEEE, CE & UKCAAdditional informations: To support the tablet without the Rugged Boot, see RAP-INSERT-ZE21U.This dock is not compatible with IntelliSkin.For IntelliSkin with GDS Tech, see RAM-GDS-DOCK-ZE21PDU.Devices shown are not included in the delivery.Only the RAM-HOL-ZE21PDU holder is supplied.
SKU
RAM-HOL-ZE21PDU
Warranty
Quantity
0
Price
€145.55
Out of stock
RAM Mounts Universal Printer Clamp for Portable Printers
The RAM Quick Draw™ Jr. holder uses a unique patent pending spring loaded mechanism that holds strong, yet provides easy removal for printer storage. At each end of the cradles are side clamping plates that are designed to fit cleanly around the edges of a printer. Compatible Printers: Fujitsu FP-1000 Clamping Dimensions: Width: Min 5.625” to Max 9.5” Height: Max 1.75” Material: Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display. Description: RAM® Suction Cups are regarded as one of the most impressive suction cups in the world. Their incredible holding power is surprising when considering how most suction cups function. When two suction cups are used together the performance is amazing. The RAM® Dual Articulating Suction Cup is an amazing innovation in suction cup mounting. With the ability to independently articulate each suction cup, this mounting base can be used in a variety of applications such as curved windows and surfaces. Whether you are mounting to a curved surface on a vehicle, or a curved windshield, this product is the ideal solution for secure suction cup mounting. Features: 1. Customize mounting position for convex and concave surfaces by repositioning suction cup bases 2. Dual suction cups provide extra strength and stability for devices up to 5 lbs. 3. Commercial grade product for unparalleled performance 4. Dual suction cups for redundancy 5. High strength materials maximize longevity of the mount 6. Ball and socket mounting system offers ease of adjustment product adjustment 7. Lifetime warranty 8. Made in U.S.A. Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1-inch Rubber Ball -inchB-inch Size Note: The -inchU-inch in the part number reflects product packaged in poly bag. RAM MOUNT triple suction cup base to mount portable heavy electronic units in a most safest way.The middle of the construction is suitable for the round base plate. Alternatively you can also connect diamond plates on the edges. Though you are able to connect three units on one base.This exceptional product allows the freedom to use and move your electronics like never before. Ideally suited to a wide range of agricultural, commercial, and industrial uses, the triple suction cup base makes it possible to mount your electronics for optimum access, viewing, and safety.Material: High Strength Composite.Colour: black
SKU
RAM-VPR-104
Warranty
Quantity
1
Price
€76.76
Accessories:
RAM Mounts scanner holder
RAM Mounts scanner holder with magnetic Tough-Mag adapter
SKU
RAP-396-MAG88U
Warranty
Quantity
0
Price
€91.48
Out of stock